Manufacturer :- Firow Custom built Exclusively for Gwyn Lewis 4×4 to our own very specific specifications. Not to be confused with other similar looking propshafts available elsewhere.
Please select the colour you want to order from the drop down menu, we have these in BLUE or BLACK
Part Number :- GL-EXT-1065-BLUE, PUMA 110 Rear Wide Angle HD 1310 Prop Shaft
Part Number :– GL-EXT-1065-BLACK, PUMA 110 Rear Wide Angle HD 1310 Prop Shaft
Working length :- 1100mm + – 8mm
Fits:- Defender 110 Rear Puma TDCi 2.4 & 2.2
Weight :- 13.1KG
These HEAVY DUTY wide angle prop shafts are custom made for us to our own specification, they are a very well made prop shaft using the very best of components we can source, they are fully greaseable including the slider, they are balanced to a very high standard and have proved to reduce vibrations on many Land Rovers.
For those looking for our strongest prop shafts please see more info on our 2020 MEGA props HERE. These are for extreme use off roaders with large aggressive tyres and upgraded driveline.
These propshafts are made to a very high standard, please don’t compare these to cheap import ones.
Fitting advice :-
Please note these propshafts have heavy duty round flanges, when fitting make sure you clean up the diff and gearbox flange faces as you may have taken a square type flange off and the new round flange does not want to sit on top of dirt or rust. Brushing some grease on to flange faces after will help stop rust.
The Slider goes to your transfer box flanges, for a Double Cardan prop the DC end goes to the front transfer box flange.
You must ensure all UJs and the slider are fully greased on fitment and are regularly greased during use.
We Grease all UJ’s and sliders here during final checks but sliders can not be filled with grease until a prop is fitted, you will need to fill the slider with grease.
If you require a custom length, please contact us with measurements so we can get one made, have a look at the last picture to help you measure your propshaft length.
Please Note:- Puma TDCI Defenders are more prone to suffer from propshaft vibration issues due to the angle that the engine and transmission is mounted, the engine is mounted high with the transfer box mounted low, this angle makes propshaft universal joints work at steeper angles then previous generations of Defenders.
The engine is mounted high to clear the front axle, this increases front propshaft working angles, the whole transmission is moved back so that the gear sticks can come up in front of the dash, this does increase the length of the front propshaft and so help shallow back out the angle that it runs through, on a 90 though this makes the rear propshaft short so it also runs at a steeper angle, this is why the transfer box was lowered to help shallow out the angle that it runs through.
These bad angles are at standard height, after a suspension lift they only become worse.
GKN had massive problems producing propshafts for Land Rover that would cope with this problem which is why all standard front and 90 rear props on a Puma’s are so high spec, 110/130 standard rear props are the same sort of spec as older generations of Defender.
Vibration problems are very common with Puma TDCI Defenders and can be very difficult to solve. This is a vehicle problem resulting from the less than ideal position that the Puma engine and transmission is mounted.
To reduce likely hood of vibration problems with Puma Defenders we would recommend lifting up to 1” rather than 2”, that said it is not unknown for even lowered Defenders to suffer from vibration issues, it is all down to UJ working angles and how the different working angles at each end of the prop affects the overall harmonics of the shaft.
UJs do not turn at a constant velocity, as they turn they speed up and slow down, the steeper the working angle the faster they have to speed up and slow down, this speed change is where vibrations come from.
Please be aware that solving propshaft vibrations on Pumas can be very difficult, steep propshaft universal joint angles cause vibration issues.
- 30 degree wide angle (1310 series) to prevent the propshaft binding up on long travel suspension.
- Large 3 inch heavy duty 3mm wall tube.
- Higher torque capacity than a standard Land Rover propshaft.
- Heavy duty round flange face (not the old square type), that bolts onto the diff and gearbox 79.4mm PCD.
- Heavy duty 1310 series Universal Joints (81.8mm x 27mm) with nylon thrust washers and nylon/rubber seals, the nylon thrust washers also have 5 slots in them to allow grease to get to each cup when greasing them (see picture of joint you can see the 5 slots in the thrust washer).
- Rilsan coated spline for smother operation and helps eliminate vibrations.
- Upgraded involute spline configuration with 18 splines that is also GREASABLE which is a feature only found on our propshafts.
- Double seal arrangement on the slip assembly, with 110mm of movement and full spline contact on the male and female slider to help with long travel suspension.
- Internally plug welded to hold grease in the slider.
- Phased when required to reduce vibrations.
- All prop shafts come with a tube of k48 grease.
Propshaft vibrations on lifted vehicles can be a problem. Lifts of 2” and above (1” with Puma TDCI) start to steepen propshaft Universal Joint working angles to the point where vibration problems can become an issue.
Caster Correction also steepens UJ working angles so can bring on more vibration problems.
A classic scenario where you will feel worst vibrations is on overrun, around 50mph where you are not accelerating or engine braking, the whole transmission is “slack” on overrun.
The centre diff inside the transferbox can “rattle” around at this point. There are only supporting bearings at the front and rear output flanges of a transfer box, the two halves of the output shafts and the centre diff just “float” in the middle of the transferbox, these are all unbalanced parts and can themselves be the cause of transmission vibrations.
A Double Cardan propshaft is often successful in helping to solve these vibration problems but it is not a true cure, it can hide the problem to the point where it is not noticed or becomes reduced enough that it can be tolerated.
A Double Cardan propshaft has two UJs at the Double Cardan end, between the 2 joints there is a ball and cup that holds the 2 joints together, this is positioned at the front transferbox flange (where the steepest working angle is on all Land Rovers) These two UJs together halve the angle felt at the transferbox, halving that angle helps to reduce the vibration problem caused by steep running angles.
A Wide Angle propshaft alone is not always enough to help with vibration problems, a good quality Wide Angle prop can be enough to solve some vibration problems but the UJ’s are still working at the same angles as a standard prop, it is steep running angles that cause vibrations.
A Wide Angle propshaft can turn through a wider angle before yokes bind, this is to accommodate long travel suspension movements (axle drop out) off road, it does not mean that the propshaft can be run at steep angles on road at road speeds (big suspension lifts). UJ’s will wear quicker when run at steep angles. Ideally for road work UJ’s should be running between 2 to 10 degrees, beyond 10 degrees quicker wear and vibrations can become an issue.
Properly spec’d Wide Angle and Double Cardan propshafts should be made with long slip sliders, this is to accommodate long travel suspension, you need more slip with increased ride height and axle drop. A propshaft spacer should NEVER be used for any reason. By adding a spacer to close up a slider after a lift or to allow for more axle drop you are in fact increasing the closed length of the propshaft, off road your axles not only need to move downwards they also need to move upwards, using a spacer to close up a slider that is too short will mean your propshaft can not close up enough to fit in the space between tranferbox and diff flanges, you will cause damage to your drive line if your propshaft can not close up enough.
To reduce likely hood of vibration problems we would recommend not lifting more than 2” (1” with Puma TDCI), that said it is not unknown for even lowered Defenders to suffer from vibration issues, it is all down to UJ working angles and how the different working angles at each end of the propshaft affects the overall harmonics of the shaft.
UJs do not turn at a content velocity, as they turn they speed up and slow down, the steeper the working angle the faster they have to speed up and slow down, this speed change is where vibrations come from.
Please note that prop shaft UJ`s on lifted vehicles are under more strain and require REGULAR GREASING to prolong their life. No prop shaft should be run for long periods of time with a steeper running angle of more than 10 degrees, anything above this angle used for long journeys will cause the UJs to overheat and cause premature wear. This is always a problem on Land Rovers, especially with suspension lifts above 2 inches as once you lift the suspension the prop shaft angle steepens, even caster correction makes the prop shaft angle steeper.
We can also make non standard custom length props.
If you are unsure what you need please contact me.